Alpha-Test: Repeater, die sich selbst updaten
Du flasht mehrere Testrepeater mit 1.17.1-b2 und einen mit 1.18.0-b3. Dann siehst du zu, ob die anderen sich per Funk selbst auf 1.18 bringen. Nimm nur Knoten, die du gut erreichst und für den Test entbehren kannst.
Stand 16. November 2026: Wir haben die Pakete 1.17.1-b2 und 1.18.0-b3 zurückgezogen.
Bitte starte damit keinen neuen Test. Für einen zweiten Test kommen neue Pakete, sie stehen dann hier.
Die Dateinamen und Prüfsummen unten gehören zu den zurückgezogenen Paketen. Im Alpha-Feld läuft seit dem 12. November 2026 die Kampagne dc7b7cb0 (Build 3) mit zwei Tester-Knoten im Feld beobachtet.
Der Analyzer (Stand 13. November 2026) hört sie nur direkt (Zero-Hop) über einen Beobachter im Feld beobachtet.
Ohne Standard-Region gibt es keine Statusmeldung. Der Lauf ist nicht vollständig offen.
Alpha test: repeaters that update themselves
You flash several test repeaters with 1.17.1-b2 and one with 1.18.0-b3. Then you watch whether the others bring themselves to 1.18 over the air. Use only nodes that you can reach easily and can spare for the test.
Status as of 16 November 2026: We have withdrawn the packages 1.17.1-b2 and 1.18.0-b3.
Please do not start a new test with them. New packages for a second test will follow and will be listed here.
The file names and checksums below belong to the withdrawn packages. The field campaign dc7b7cb0 (build 3) has run since 12 November 2026. It has two tester nodes observed in the field.
The analyzer (as of 13 November 2026) hears it only directly (zero-hop) through one observer observed in the field.
Without a default region there is no status message. The run is not complete open.
So läuft der Test
How the test runs
- Such dir ein paar andere Tester und bildet eine Gruppe. Ihr teilt mehrere Testrepeater unter euch auf. Alle Geräte der Gruppe liegen in Funkreichweite zueinander.
- Alle flashen das Basispaket 1.17.1-b2 per USB (Tabelle unten) und setzen die Region ihres Netzes (Abschnitt Region setzen).
- Genau einer macht den Seed. Er flasht auf einen der Testrepeater das Seed-Paket 1.18.0-b3.
- Die anderen holen das Update per Funk, prüfen die Signatur, starten zur Probe und bestätigen. Du tust nichts.
- Du beobachtest den Stand und meldest, was passiert ist.
Richte jeden Testrepeater ein wie jeden anderen Repeater. Tippe die Befehle in der USB-Konsole.
- Admin-Passwort:
password <Passwort>, höchstens 15 Zeichen. Die Alpha-Pakete sind Release-Images und haben ab Werk keines. Für die USB-Befehle brauchst du es nicht, es gilt für den Admin-Zugang aus der Ferne. Der Knoten antwortet mitpassword now:und dem Passwort im Code geprüft. Mit einem Release-Image am Gerät ist das noch nicht gemessen offen. - Das Passwort
passwordgeht nicht, ein leeres auch nicht. Ein Release-Image lehnt beide beim Admin-Login ab, auch wenn alte gespeicherte Einstellungen sie enthalten im Code geprüft. Werpassword passwordtippt, bekommt die ZeileErr - no admin login with an empty password (in a release: nor with the stock default)im Code geprüft. Wähle ein anderes Passwort. Mit einem Release-Image am Gerät ist das noch nicht gemessen offen. - GPS-Position:
set lat <Breite>undset lon <Länge>. Die Antwort ist jeweilsOKim Code geprüft. - Name mit der Startversion:
set name FUOTA-Test 1.17auf den Repeatern mit 1.17.1-b2,set name FUOTA-Test 1.18auf dem Seed. Die Antwort istOK. So siehst du im Analyzer, welcher Repeater welcher ist. Der Name geht mit dem nächsten Advert raus,advertsendet ihn sofort im Code geprüft. Er bleibt nach einem Update stehen, auch wenn der Repeater dann 1.18 trägt im Code geprüft. Für ein Update per Funk ist das am Gerät noch nicht gemessen offen. - LoRa-Parameter:
set radio <MHz>,<Bandbreite>,<SF>,<CR>mit den Werten deines Netzes. Die Antwort istOK - reboot to apply, danach startest du den Knoten neu im Code geprüft. - Region: siehe Abschnitt Region setzen.
- Advert-Intervall:
set advert.interval 240. 1.17.1-b2 erlaubt 0 (aus) und 60 bis 240 Minuten im Code geprüft. 1.18.0-b3 erlaubt 0 und 60 bis 510 Minuten im Code geprüft. Der Wert 240 gilt in beiden Versionen. 1.17.1-b2 startet mit einem Intervall unter 60 Minuten und setzt es beim ersten Speichern einer Einstellung auf 0 im Code geprüft. Dann sendet der Knoten keine Adverts mehr und erscheint nicht im Analyzer. Der Seed 1.18.0-b3 startet bei einer Neuinstallation mit 360 Minuten im Code geprüft. - Repeat an lassen:
get repeatzeigt> on, ab Werk ist es an. Mitset repeat onschaltest du es wieder ein, die Antwort istOK - repeat is now ON. Mitset repeat offgibt der Knoten Updates nur an direkte Nachbarn weiter im Code geprüft.
Mehrere Gruppen können unabhängig voneinander testen, je mehr, desto besser. Ohne Gruppe geht es auch allein mit zwei Geräten: eines mit 1.17.1-b2 als Empfänger, eines mit dem Seed-Paket.
- Find a few other testers and form a group. You split several test repeaters among yourselves. All devices of the group are within radio range of each other.
- Everyone flashes the base package 1.17.1-b2 over USB (table below) and sets the region of their network (section Setting the region).
- Exactly one person makes the seed. They flash the seed package 1.18.0-b3 onto one of the test repeaters.
- The others fetch the update over the air, check the signature, start it on trial and confirm. You do nothing.
- You watch the state and report what happened.
Set up every test repeater like any other repeater. Type the commands in the USB console.
- Admin password:
password <password>, 15 characters at most. The alpha packages are release images and have none from the factory. You do not need it for the USB commands, it is for admin access from afar. The node answers withpassword now:and the password checked in the code. With a release image on a device this is not yet measured open. - The password
passworddoes not work, and neither does an empty one. A release image refuses both at the admin login, even when old saved settings hold them checked in the code. If you typepassword password, you get the lineErr - no admin login with an empty password (in a release: nor with the stock default)checked in the code. Choose another password. With a release image on a device this is not yet measured open. - GPS position:
set lat <latitude>andset lon <longitude>. Each answer isOKchecked in the code. - Name with the starting version:
set name FUOTA-Test 1.17on the repeaters with 1.17.1-b2,set name FUOTA-Test 1.18on the seed. The answer isOK. That way you can tell in the analyzer which repeater is which. The name goes out with the next advert, andadvertsends it at once checked in the code. It stays after an update, even when the repeater then runs 1.18 checked in the code. For an update over the air, this is not yet measured on a device open. - LoRa parameters:
set radio <MHz>,<bandwidth>,<SF>,<CR>with the values of your network. The answer isOK - reboot to apply, then you restart the node checked in the code. - Region: see the section Setting the region.
- Advert interval:
set advert.interval 240. 1.17.1-b2 allows 0 (off) and 60 to 240 minutes checked in the code. 1.18.0-b3 allows 0 and 60 to 510 minutes checked in the code. The value 240 is valid in both versions. 1.17.1-b2 starts with an interval under 60 minutes and sets it to 0 when you first save a setting checked in the code. Then the node sends no adverts and does not show up in the analyzer. The seed 1.18.0-b3 starts at 360 minutes on a new install checked in the code. - Keep repeat on:
get repeatshows> on, it is on from the factory. Withset repeat onyou switch it back on, the answer isOK - repeat is now ON. Withset repeat offthe node passes updates on to direct neighbours only checked in the code.
Several groups can test independently of each other, the more the better. Without a group it also works alone with two devices: one with 1.17.1-b2 as the receiver, one with the seed package.
Region setzen
Setting the region
Setze auf jedem Testrepeater die Region deines Netzes als Default. Gib in der USB-Konsole
region default hansemesh ein. Der Knoten antwortet default scope is now hansemesh.
Das Beispiel gilt für HanseMesh. Regionsnamen sind Freitext und je Netz verschieden. Nimm den Namen deines Netzes.
Die Region bleibt gespeichert, auch über einen Neustart gemessen.
Ohne Standard-Region zeigt der Analyzer keinen Repeater mit Statusmeldung. Der Knoten verwirft seine
Statusmeldungen (fuota: status E3 not sent, no default region). Seine Update-Angebote gehen nur an
direkte Nachbarn (fuota info: no default region: not flooded)
gemessen.
Mit Region sendet der Knoten die Statusmeldungen in die Region gemessen. Auch seine Update-Angebote flutet er dann dorthin im Code geprüft. Statusmeldungen sind gedrosselt, höchstens 8 in 24 Stunden.
On every test repeater, set the region of your network as the default. In the USB console, enter
region default hansemesh. The node answers default scope is now hansemesh.
The example is for HanseMesh. Region names are free text and differ from network to network. Use the name of
your network. The region stays stored, even across a restart measured.
Without a default region, the analyzer shows no repeater with a status message. The node discards its status
messages (fuota: status E3 not sent, no default region). Its update offers only reach direct
neighbours (fuota info: no default region: not flooded)
measured.
With a region, the node sends its status messages into the region measured. It then floods its update offers there too checked in the code. Status messages are throttled, at most 8 in 24 hours.
Beobachten
Watching
fuota info zeigt am Gerät den Stand in der USB-Konsole. Als angemeldeter Admin fragst du ihn auch
übers Mesh ab im Code geprüft. Dort gibt fuota status nur die Kurzantwort
von fuota info, die ausführliche Anzeige gibt es nur per USB
im Code geprüft. Das ist am Gerät noch nicht gemessen offen.
Nach dem Flashen steht bei 1.17.1-b2 build 1 (6b3af727) in fuota info.
Von außen siehst du die Kampagne im Analyzer. Sie erscheint dort erst, wenn ein Observer (ein Knoten, der mithört und meldet) Angebote oder Daten hört. Steht dort keine Kampagne, gilt die Anzeige am Gerät.
Der Analyzer zeigt die Alpha-Kampagne im Feld beobachtet. Du findest sie auf der Seite FUOTA-Kampagnen im Tab Aktivität. Der Tab Rollout zeigt nur Repeater, die Statusmeldungen senden im Feld beobachtet. Das sind nur Knoten mit Standard-Region (Abschnitt Region setzen).
Der Weg zwischen Seed und Empfänger darf über normale MeshCore-Repeater (Stock) führen. Die Angebote laufen als gewöhnliche Gruppen-Daten-Flut, die Stock-Repeater nach Region weiterleiten im Code geprüft. Am Brett lief ein P1 mit unveränderter Stock-Firmware als Relais gemessen.
Im ersten Test kam das geflutete Angebot über das Mesh bis zu 6 Hops weit im Feld beobachtet. Ein Empfänger bekam Datenpakete über 2 Repeater hintereinander, von denen der Analyzer nie FUOTA-Pakete gehört hat, bis zum 15.11. 48 von 174 im Feld beobachtet. Ein ganzes Update kam auf diesem Weg noch nicht an. Viele Anfragen gingen auf dem Rückweg verloren: Von 73 gehörten Pfad-Anfragen kamen 35 beim letzten Repeater vor dem Anbieter an im Feld beobachtet.
Deshalb geht die Anfrage zuerst auf dem Rückweg des Angebots zum Anbieter. Bleibt sie zweimal ohne Antwort, schickt der Empfänger sie einmal als Flut. Der Anbieter meldet ihm den Weg zurück, den die Flut genommen hat. Danach fragt der Empfänger auf diesem Weg. Das steht im Entwicklungszweig im Code geprüft. Ob die Pakete des zweiten Tests es schon enthalten, ist offen. Melde weiter, ob Stock-Repeater dazwischen lagen.
Zum Probestart: Ein frisch aktualisierter Knoten bestätigt die neue Version erst, wenn er ein Funkpaket hört und selbst eins sendet. Dafür hat er je nach Knoten zwischen 15 Minuten und 6 Stunden Zeit. Hört er bis dahin nichts, startet er neu. Nach drei solchen Starts kehrt er zur alten Version zurück. Einen neuen Versuch gibt es frühestens nach einem Tag im Code geprüft. Teste deshalb dort, wo dein Knoten andere Knoten hört.
Zur Dauer: Der Release-Takt hat 0,3 % Sendeanteil. Mit ihm brauchte ein Knoten 12,6 h für 174 Fragmente gemessen. Das war ein einzelner Lauf am Testaufbau.
fuota info shows the state in the USB console on the device. As a logged-in admin you can also query it
over the mesh checked in the code. Over the mesh, fuota status gives only
the short answer of fuota info, and the detailed display exists only over USB
checked in the code. This is not yet measured on a device
open. After flashing, 1.17.1-b2 shows build 1 (6b3af727) in
fuota info.
From outside you can see the campaign in the analyzer. It appears there only once an observer (a node that listens and reports) hears offers or data. If no campaign shows, trust the display on the device.
The analyzer shows the alpha campaign observed in the field. You find it on the FUOTA campaigns page, in the Activity tab. The Rollout tab shows only repeaters that send status messages observed in the field. Those are only nodes with a default region (section Setting the region).
The path between seed and receiver may run through normal MeshCore repeaters (stock). The offers travel as ordinary group data floods, which stock repeaters forward by region checked in the code. On the bench a P1 with unchanged stock firmware ran as a relay measured.
In the first test the flooded offer travelled up to 6 hops through the mesh observed in the field. One receiver got data packets over 2 repeaters in a row from which the analyzer never heard FUOTA packets, 48 of 174 by 15 November observed in the field. No complete update has arrived this way yet. Many requests were lost on the way back: of 73 heard path requests, 35 reached the last repeater before the provider observed in the field.
So the request first goes back to the provider along the path the offer took. If it stays unanswered twice, the receiver sends it once as a flood. The provider reports back the path the flood took. After that the receiver asks along this path. This is in the development branch checked in the code. Whether the packages of the second test already contain it is open. Keep reporting whether stock repeaters lay in between.
On the test boot: a freshly updated node only confirms the new version once it hears a radio packet and sends one itself. Depending on the node, it has between 15 minutes and 6 hours for that. If it hears nothing by then, it restarts. After three such starts it returns to the old version. It tries again after one day at the earliest checked in the code. So test where your node hears other nodes.
On the duration: the release pace has a 0.3 % send share. At that pace a node needed 12.6 h for 174 fragments measured. That was a single run on the bench.
Sieben Tage Wartezeit und „sofort“
Seven days of delay and “now”
Ein Release-Image installiert ein fertig geholtes Update nicht sofort. Ab Werk steht auto delay: Der Knoten
gibt das Update 7 Tage lang nur weiter und installiert es danach. In dieser Woche lässt sich ein Update noch
zurückziehen. Der Release-Build lässt sich nicht mit kürzerer Wartezeit bauen im Code geprüft.
Wer nicht warten will, gibt am Knoten in der USB-Konsole fuota auto now ein. Der Knoten installiert dann,
sobald das Update vollständig da ist. Wir bitten dich, das am Anfang zu setzen.
A release image does not install a fetched update at once. The factory setting is auto delay: the node
only passes the update on for 7 days and installs it afterwards. During that week an update can still be
withdrawn. The release build cannot be built with a shorter delay checked in the code.
If you do not want to wait, type fuota auto now in the USB console of the node. The node then installs
as soon as the update is complete. We ask you to set this at the start.
Was du meldest
What you report
Am liebsten als GitHub Issue mit der Vorlage „Alpha-Bericht“: github.com/marcelverdult/meshcore_fuota. Telegram (Thread) und Discord gehen auch. Wer schon auf dem Server ist, findet die Alpha-Meldungen direkt in diesem Kanal. Kopiere Ausgaben als Text, keine Screenshots.
- Board, Dateiname und ob die Prüfsumme gepasst hat
- Version vorher und nachher (
ver,fuota info) - Zeit bis zum Update: wann es fertig war, wann
testingundconfirmedkamen - ob du
auto now,fuota apply 3oderauto delaygenutzt hast - Auszug aus dem Analyzer oder dem Log (
fuota radio,fuota status) - ob Stock-Repeater zwischen Seed und Empfänger lagen
- alles Auffällige: Neustart ohne dein Zutun, Rückfall auf 1.17.1, Meldungen mit
ERR, Strom weg
Wenn es klappt, lässt du 1.18 auf den Repeatern. Künftige Updates sollen auf demselben Weg per Funk kommen.
Sobald MeshCore 1.19 herausgibt, planen wir dafür ein FUOTA-Update. Zurück zur offiziellen MeshCore-Firmware
geht jederzeit mit fuota uf2. Sag vorher kurz Bescheid.
Preferably as a GitHub issue with the template “Alpha-Bericht”: github.com/marcelverdult/meshcore_fuota. Telegram (thread) and Discord work too. If you are already on the server, you find the alpha reports directly in this channel. Copy output as text, not screenshots.
- board, file name and whether the checksum matched
- version before and after (
ver,fuota info) - time to the update: when it was complete, when
testingandconfirmedcame - whether you used
auto now,fuota apply 3orauto delay - an excerpt from the analyzer or the log (
fuota radio,fuota status) - whether stock repeaters lay between seed and receiver
- anything unusual: a restart without your doing, a fall back to 1.17.1, messages with
ERR, power loss
If it works, you keep 1.18 on the repeaters. Future updates are meant to arrive the same way over the air.
Once MeshCore releases 1.19, we plan a FUOTA update for it. You can go back to the official MeshCore firmware
at any time with fuota uf2. Tell us briefly beforehand.
Pakete für 18 Boards
Packages for 18 boards
Nimm die Datei mit deinem Board im Namen und vergleiche die Prüfsumme mit SHA256SUMS aus dem Release.
Das SoftDevice im Dateinamen muss zur Zeile SoftDevice: in INFO_UF2.TXT deines Geräts passen.
Zum Flashen drückst du zweimal Reset und ziehst die Datei auf das Laufwerk. Ohne USB-Zugang geht es per Bluetooth
(Abschnitt „Ohne USB“ unten).
Die Alpha-Pakete haben keinen Display-Treiber. Ein vorhandenes Display, zum Beispiel am Heltec T114, zeigt nichts an. Das ist so vorgesehen im Code geprüft.
Die Pakete tragen ein gemeinsames Image für 18 Boards. Sechs davon sind am Gerät gesehen: FakeTec, SenseCAP P1, RAK4631, T114, Xiao und T096. Zwölf sind nur gebaut und am Rechner geprüft, am Gerät nicht bestätigt offen.
Xiao und T096 liefen am 11. November 2026 am Testaufbau bei SF7 und 1 dBm. Beide Boards wurden am Deskriptor erkannt, der Funk lief gemessen. Zero-Hop-Pakete gingen mit einem FakeTec in beide Richtungen gemessen. Nicht geprüft sind FUOTA-Pull über Funk, LED und Taste, serielles DFU und Rückfall offen.
Das Seed-Paket heißt wie das Basispaket, mit 1.18.0-b3 statt 1.17.1-b2 und seed
statt base. Für 1.18.0-b3 gibt es nur Seed-Pakete, auch für eine spätere Installation von Hand: Sie enthalten dieselbe Firmware und zusätzlich die Kampagne. Die Prüfsummen stehen in SHA256SUMS des Releases alpha-118-b3 und unten in der zweiten Tabelle.
Take the file with your board in its name and compare its checksum with SHA256SUMS from the release.
The SoftDevice in the file name must match the SoftDevice: line in INFO_UF2.TXT of your device.
To flash, press reset twice and drag the file onto the drive. Without USB access it works over Bluetooth
(section “Without USB” below).
The alpha packages have no display driver. A display that is present, for example on the Heltec T114, shows nothing. That is intended checked in the code.
The packages carry one shared image for 18 boards. Six were seen on a device: FakeTec, SenseCAP P1, RAK4631, T114, Xiao and T096. Twelve are only built and checked on the host, not confirmed on a device open.
Xiao and T096 ran on the bench on 11 November 2026. They used SF7 and 1 dBm. Both boards were recognised by their descriptor, and the radio ran measured. Zero-hop packets went in both directions with a FakeTec measured. Not tested: FUOTA pull over the air, LED and button, serial DFU and revert open.
The seed package is named like the base package, with 1.18.0-b3 instead of 1.17.1-b2 and
seed instead of base. For 1.18.0-b3 there are only seed packages, also for a later manual install: they contain the same firmware plus the campaign. The checksums are in SHA256SUMS of the release alpha-118-b3 and in the second table below.
| Board | Basispaket 1.17.1-b2 für alle Geräte | sha256 |
|---|---|---|
| FakeTec | meshcore-fuota-1.17.1-b2-base-faketec-s140-6.1.1.uf2 | 98fa9e392d57bedcadf9cc193dc5763f239ce6d594cefda4be398cb60f51630a |
| Seeed SenseCAP Solar P1 | meshcore-fuota-1.17.1-b2-base-p1-s140-7.3.0.uf2 | 26fb2f9c230632b8638f27b4f6b2a40de173d8176ddeffe9e2881449be953d82 |
| RAK4631 | meshcore-fuota-1.17.1-b2-base-rak4631-s140-6.1.1.uf2 | ec0477306f17aa1ee944973b767df527f513b36ab7a0c76c825add3e7c735bc9 |
| Heltec T114 | meshcore-fuota-1.17.1-b2-base-t114-s140-6.1.1.uf2 | 0ea95d55956fe0239e6290c3b57a1bc5bbe7e41dfcb8f937dfa6c0f7342230fb |
| Seeed XIAO nRF52 | meshcore-fuota-1.17.1-b2-base-xiao-s140-7.3.0.uf2 | 3471e2a316f66a991e003d6aad4e84adfdedf729fa1d4255a909456f06654dc9 |
| Heltec T096 | meshcore-fuota-1.17.1-b2-base-t096-s140-6.1.1.uf2 | 77c5dbe2d4a117da558332c54dc2045402d80dba087600ddfcaf99dc384b0649 |
| GAT562 Mesh Tracker Pro | meshcore-fuota-1.17.1-b2-base-gat562_tracker-s140-6.1.1.uf2 | 3afff03000ea8d1a09b10d76e8c45c379d6c6e791851cbbc00bfd8140ed6ed04 |
| GAT562 Mesh EVB Pro | meshcore-fuota-1.17.1-b2-base-gat562_evb-s140-6.1.1.uf2 | 1e01ab9b413b8291a7678fef5106bdaf20478520d1040733128899c9dbeeceec |
| GAT562 30S Mesh Kit | meshcore-fuota-1.17.1-b2-base-gat562_30s-s140-6.1.1.uf2 | 19f955c11f52713f4956d61eea33ebc7fe2b2316a852d9cd24e6812a92573812 |
| RAK WisMesh Tag | meshcore-fuota-1.17.1-b2-base-wismesh_tag-s140-6.1.1.uf2 | 6531e78373bba3ee6004b865091803f3e247fb3ea2a3de1e88b5cbde701029b3 |
| Elecrow ThinkNode M1 | meshcore-fuota-1.17.1-b2-base-thinknode_m1-s140-6.1.1.uf2 | e4375facab2645a0bc96e32753e4c1e76756f244c5aa924693205d0f1e4bddd8 |
| Elecrow ThinkNode M6 | meshcore-fuota-1.17.1-b2-base-thinknode_m6-s140-6.1.1.uf2 | 435adaa769616ff8d3897c5a547220b874ce36cd007b6e940aa44958ef0522de |
| Keepteen LT1 | meshcore-fuota-1.17.1-b2-base-keepteen_lt1-s140-6.1.1.uf2 | 64e04628edb7ed56e4c19c23d9d625fb065c486c196f79dbe85c169bd74322e8 |
| LilyGo T-Echo | meshcore-fuota-1.17.1-b2-base-lilygo_techo-s140-6.1.1.uf2 | 3f9127b265516a77e90a0a15964db14c94f0e0224b07dfff830b527cc235f98e |
| Heltec Mesh Pocket | meshcore-fuota-1.17.1-b2-base-mesh_pocket-s140-6.1.1.uf2 | febfa88206a0394ae6038c589dad800d72ea3646bc2650ae7310f415af7145cf |
| Seeed Wio Tracker L1 | meshcore-fuota-1.17.1-b2-base-wio_tracker_l1-s140-7.3.0.uf2 | 8e9c1d694616682be23c7a192c2f4ca92e78a4e9929b42cebc0550f6815db418 |
| muzi works R1 Neo | meshcore-fuota-1.17.1-b2-base-muzi_r1_neo-s140-6.1.1.uf2 | beca18b0f8d9eecb2ef1c57bb4203906267d045d59f637305e26bcda27608ce1 |
| Nano G2 Ultra | meshcore-fuota-1.17.1-b2-base-nano_g2_ultra-s140-6.1.1.uf2 | 82af64c909151a6a4ac549581066fffa3d59053ae66bdf3e48306997971f2954 |
| Board | Seed-Paket 1.18.0-b3 mit Kampagne | sha256 |
|---|---|---|
| FakeTec | meshcore-fuota-1.18.0-b3-seed-faketec-s140-6.1.1.uf2 | 291a28880ed52f39a782dd55530fd07fac9b0240606ca5f70bf019711135eb56 |
| Seeed SenseCAP Solar P1 | meshcore-fuota-1.18.0-b3-seed-p1-s140-7.3.0.uf2 | 4eb1418a17402a72e45659456a1047f57d2b7520c95d010364e0bd671f8f4980 |
| RAK4631 | meshcore-fuota-1.18.0-b3-seed-rak4631-s140-6.1.1.uf2 | 46bf8ab8caa9f6d9dd99f93481c58c65461b10b17899171d8d6829993ae1e456 |
| Heltec T114 | meshcore-fuota-1.18.0-b3-seed-t114-s140-6.1.1.uf2 | f92d966b2f19cbb194d7ee6c00f11fee10f08b4a81391843c1e574ce1b104d88 |
| Seeed XIAO nRF52 | meshcore-fuota-1.18.0-b3-seed-xiao-s140-7.3.0.uf2 | a619a740f36e58c033e959699f709af6417ca08df69f5a0a6c284a144478aa32 |
| Heltec T096 | meshcore-fuota-1.18.0-b3-seed-t096-s140-6.1.1.uf2 | d32479f3dcbafbaf8def412d40bb40a9297199378f5c8a6754162811e75f678b |
| GAT562 Mesh Tracker Pro | meshcore-fuota-1.18.0-b3-seed-gat562_tracker-s140-6.1.1.uf2 | f99c693877239d4842adc472deb1d329816c1af46d8a476b477d310e37fabebb |
| GAT562 Mesh EVB Pro | meshcore-fuota-1.18.0-b3-seed-gat562_evb-s140-6.1.1.uf2 | 715710921926c7d6e0a24ab6266f4892e542c421a918252e45b97c758978e5ee |
| GAT562 30S Mesh Kit | meshcore-fuota-1.18.0-b3-seed-gat562_30s-s140-6.1.1.uf2 | 50559b01bf44b554cb2ddd31dd4a68af1a8bd20a0136f5f83271d3dcc5e9929e |
| RAK WisMesh Tag | meshcore-fuota-1.18.0-b3-seed-wismesh_tag-s140-6.1.1.uf2 | af2a597ac389f55e131e4d0de1483575a40d8a9bc22e141dfaefb339ad57d9bc |
| Elecrow ThinkNode M1 | meshcore-fuota-1.18.0-b3-seed-thinknode_m1-s140-6.1.1.uf2 | a5d75e3f63a62becc46ec5d2fdf3a7a9d99a0d0f446901dc291ff4ffe42bde39 |
| Elecrow ThinkNode M6 | meshcore-fuota-1.18.0-b3-seed-thinknode_m6-s140-6.1.1.uf2 | b2ba54e1b82952879541232dbbb05eaa4f2d6ba350638408bb34d5a2ec111b92 |
| Keepteen LT1 | meshcore-fuota-1.18.0-b3-seed-keepteen_lt1-s140-6.1.1.uf2 | df49736c63884cc6b3fc5c0b359801be773048f79cffaa28285579d5ca1f1f5e |
| LilyGo T-Echo | meshcore-fuota-1.18.0-b3-seed-lilygo_techo-s140-6.1.1.uf2 | 6c5938ca4134e9c0554efcbee9c854e5c1013fe4f8fa9c527b929f4b8df32240 |
| Heltec Mesh Pocket | meshcore-fuota-1.18.0-b3-seed-mesh_pocket-s140-6.1.1.uf2 | d56560f48815ad57b13fe425776727ecdc9e966328ac77d170975934a04edd7e |
| Seeed Wio Tracker L1 | meshcore-fuota-1.18.0-b3-seed-wio_tracker_l1-s140-7.3.0.uf2 | 2da09ca692fba63ffc4dc1f551737ba382313c5501a9c1ad5246d4de5e59b810 |
| muzi works R1 Neo | meshcore-fuota-1.18.0-b3-seed-muzi_r1_neo-s140-6.1.1.uf2 | 0a99d0040e64c757409256b51fcbfa5563782bb87ac79ca4e7f1b5a3ed7c104d |
| Nano G2 Ultra | meshcore-fuota-1.18.0-b3-seed-nano_g2_ultra-s140-6.1.1.uf2 | 12eac31990342014e14bfb482c77b5129e732d2be640bc133e06054b2c7ed9b7 |
| Board | Base package 1.17.1-b2 for all devices | sha256 |
|---|---|---|
| FakeTec | meshcore-fuota-1.17.1-b2-base-faketec-s140-6.1.1.uf2 | 98fa9e392d57bedcadf9cc193dc5763f239ce6d594cefda4be398cb60f51630a |
| Seeed SenseCAP Solar P1 | meshcore-fuota-1.17.1-b2-base-p1-s140-7.3.0.uf2 | 26fb2f9c230632b8638f27b4f6b2a40de173d8176ddeffe9e2881449be953d82 |
| RAK4631 | meshcore-fuota-1.17.1-b2-base-rak4631-s140-6.1.1.uf2 | ec0477306f17aa1ee944973b767df527f513b36ab7a0c76c825add3e7c735bc9 |
| Heltec T114 | meshcore-fuota-1.17.1-b2-base-t114-s140-6.1.1.uf2 | 0ea95d55956fe0239e6290c3b57a1bc5bbe7e41dfcb8f937dfa6c0f7342230fb |
| Seeed XIAO nRF52 | meshcore-fuota-1.17.1-b2-base-xiao-s140-7.3.0.uf2 | 3471e2a316f66a991e003d6aad4e84adfdedf729fa1d4255a909456f06654dc9 |
| Heltec T096 | meshcore-fuota-1.17.1-b2-base-t096-s140-6.1.1.uf2 | 77c5dbe2d4a117da558332c54dc2045402d80dba087600ddfcaf99dc384b0649 |
| GAT562 Mesh Tracker Pro | meshcore-fuota-1.17.1-b2-base-gat562_tracker-s140-6.1.1.uf2 | 3afff03000ea8d1a09b10d76e8c45c379d6c6e791851cbbc00bfd8140ed6ed04 |
| GAT562 Mesh EVB Pro | meshcore-fuota-1.17.1-b2-base-gat562_evb-s140-6.1.1.uf2 | 1e01ab9b413b8291a7678fef5106bdaf20478520d1040733128899c9dbeeceec |
| GAT562 30S Mesh Kit | meshcore-fuota-1.17.1-b2-base-gat562_30s-s140-6.1.1.uf2 | 19f955c11f52713f4956d61eea33ebc7fe2b2316a852d9cd24e6812a92573812 |
| RAK WisMesh Tag | meshcore-fuota-1.17.1-b2-base-wismesh_tag-s140-6.1.1.uf2 | 6531e78373bba3ee6004b865091803f3e247fb3ea2a3de1e88b5cbde701029b3 |
| Elecrow ThinkNode M1 | meshcore-fuota-1.17.1-b2-base-thinknode_m1-s140-6.1.1.uf2 | e4375facab2645a0bc96e32753e4c1e76756f244c5aa924693205d0f1e4bddd8 |
| Elecrow ThinkNode M6 | meshcore-fuota-1.17.1-b2-base-thinknode_m6-s140-6.1.1.uf2 | 435adaa769616ff8d3897c5a547220b874ce36cd007b6e940aa44958ef0522de |
| Keepteen LT1 | meshcore-fuota-1.17.1-b2-base-keepteen_lt1-s140-6.1.1.uf2 | 64e04628edb7ed56e4c19c23d9d625fb065c486c196f79dbe85c169bd74322e8 |
| LilyGo T-Echo | meshcore-fuota-1.17.1-b2-base-lilygo_techo-s140-6.1.1.uf2 | 3f9127b265516a77e90a0a15964db14c94f0e0224b07dfff830b527cc235f98e |
| Heltec Mesh Pocket | meshcore-fuota-1.17.1-b2-base-mesh_pocket-s140-6.1.1.uf2 | febfa88206a0394ae6038c589dad800d72ea3646bc2650ae7310f415af7145cf |
| Seeed Wio Tracker L1 | meshcore-fuota-1.17.1-b2-base-wio_tracker_l1-s140-7.3.0.uf2 | 8e9c1d694616682be23c7a192c2f4ca92e78a4e9929b42cebc0550f6815db418 |
| muzi works R1 Neo | meshcore-fuota-1.17.1-b2-base-muzi_r1_neo-s140-6.1.1.uf2 | beca18b0f8d9eecb2ef1c57bb4203906267d045d59f637305e26bcda27608ce1 |
| Nano G2 Ultra | meshcore-fuota-1.17.1-b2-base-nano_g2_ultra-s140-6.1.1.uf2 | 82af64c909151a6a4ac549581066fffa3d59053ae66bdf3e48306997971f2954 |
| Board | Seed package 1.18.0-b3 with campaign | sha256 |
|---|---|---|
| FakeTec | meshcore-fuota-1.18.0-b3-seed-faketec-s140-6.1.1.uf2 | 291a28880ed52f39a782dd55530fd07fac9b0240606ca5f70bf019711135eb56 |
| Seeed SenseCAP Solar P1 | meshcore-fuota-1.18.0-b3-seed-p1-s140-7.3.0.uf2 | 4eb1418a17402a72e45659456a1047f57d2b7520c95d010364e0bd671f8f4980 |
| RAK4631 | meshcore-fuota-1.18.0-b3-seed-rak4631-s140-6.1.1.uf2 | 46bf8ab8caa9f6d9dd99f93481c58c65461b10b17899171d8d6829993ae1e456 |
| Heltec T114 | meshcore-fuota-1.18.0-b3-seed-t114-s140-6.1.1.uf2 | f92d966b2f19cbb194d7ee6c00f11fee10f08b4a81391843c1e574ce1b104d88 |
| Seeed XIAO nRF52 | meshcore-fuota-1.18.0-b3-seed-xiao-s140-7.3.0.uf2 | a619a740f36e58c033e959699f709af6417ca08df69f5a0a6c284a144478aa32 |
| Heltec T096 | meshcore-fuota-1.18.0-b3-seed-t096-s140-6.1.1.uf2 | d32479f3dcbafbaf8def412d40bb40a9297199378f5c8a6754162811e75f678b |
| GAT562 Mesh Tracker Pro | meshcore-fuota-1.18.0-b3-seed-gat562_tracker-s140-6.1.1.uf2 | f99c693877239d4842adc472deb1d329816c1af46d8a476b477d310e37fabebb |
| GAT562 Mesh EVB Pro | meshcore-fuota-1.18.0-b3-seed-gat562_evb-s140-6.1.1.uf2 | 715710921926c7d6e0a24ab6266f4892e542c421a918252e45b97c758978e5ee |
| GAT562 30S Mesh Kit | meshcore-fuota-1.18.0-b3-seed-gat562_30s-s140-6.1.1.uf2 | 50559b01bf44b554cb2ddd31dd4a68af1a8bd20a0136f5f83271d3dcc5e9929e |
| RAK WisMesh Tag | meshcore-fuota-1.18.0-b3-seed-wismesh_tag-s140-6.1.1.uf2 | af2a597ac389f55e131e4d0de1483575a40d8a9bc22e141dfaefb339ad57d9bc |
| Elecrow ThinkNode M1 | meshcore-fuota-1.18.0-b3-seed-thinknode_m1-s140-6.1.1.uf2 | a5d75e3f63a62becc46ec5d2fdf3a7a9d99a0d0f446901dc291ff4ffe42bde39 |
| Elecrow ThinkNode M6 | meshcore-fuota-1.18.0-b3-seed-thinknode_m6-s140-6.1.1.uf2 | b2ba54e1b82952879541232dbbb05eaa4f2d6ba350638408bb34d5a2ec111b92 |
| Keepteen LT1 | meshcore-fuota-1.18.0-b3-seed-keepteen_lt1-s140-6.1.1.uf2 | df49736c63884cc6b3fc5c0b359801be773048f79cffaa28285579d5ca1f1f5e |
| LilyGo T-Echo | meshcore-fuota-1.18.0-b3-seed-lilygo_techo-s140-6.1.1.uf2 | 6c5938ca4134e9c0554efcbee9c854e5c1013fe4f8fa9c527b929f4b8df32240 |
| Heltec Mesh Pocket | meshcore-fuota-1.18.0-b3-seed-mesh_pocket-s140-6.1.1.uf2 | d56560f48815ad57b13fe425776727ecdc9e966328ac77d170975934a04edd7e |
| Seeed Wio Tracker L1 | meshcore-fuota-1.18.0-b3-seed-wio_tracker_l1-s140-7.3.0.uf2 | 2da09ca692fba63ffc4dc1f551737ba382313c5501a9c1ad5246d4de5e59b810 |
| muzi works R1 Neo | meshcore-fuota-1.18.0-b3-seed-muzi_r1_neo-s140-6.1.1.uf2 | 0a99d0040e64c757409256b51fcbfa5563782bb87ac79ca4e7f1b5a3ed7c104d |
| Nano G2 Ultra | meshcore-fuota-1.18.0-b3-seed-nano_g2_ultra-s140-6.1.1.uf2 | 12eac31990342014e14bfb482c77b5129e732d2be640bc133e06054b2c7ed9b7 |
Ohne USB: Update per Bluetooth
Without USB: update over Bluetooth
Kommst du an dein Gerät nicht per USB heran, nimm die OTA-ZIP-Datei. Sie bringt dieselbe Firmware wie die UF2 per Bluetooth auf das Gerät. Jedes Release führt 18 ZIP-Dateien.
Am Gerät liefen zwei Boards, je mit Basis-ZIP und Seed-ZIP, je ein Lauf gemessen.
Es sind der Seeed SenseCAP Solar P1 (S140 7.3.0) und ein FakeTec (S140 6.1.1, Bootloader
0.9.2-OTAFIX2.3-BP1.4 laut INFO_UF2.TXT).
Mit einem älteren Bootloader (OTAFIX 1.x,
DFU-Name AdaDFU) ist der Weg nicht belegt offen. Ein FakeTec, das als
AdaDFU warb, verlor bei schwachem Signal Pakete. Nach dem Aktivieren meldete es sich weder am USB noch
per Bluetooth zurück. Die Ursache ist offen. Der Name passt zu OTAFIX 1.x, die Version selbst ist nicht gemessen.
Mit dem Handy ist der Weg ungetestet offen. Die übrigen Boards liefen nie per
Bluetooth.
Hast du USB, flashe lieber die UF2. Lies vor dem Update die Zeile in INFO_UF2.TXT, die mit
UF2 Bootloader beginnt. Steht dort OTAFIX 1.x, nimm die UF2.
- Nimm den Namen der UF2 ohne
.uf2, dazu-ota.zip. Die Basis-ZIPs liegen im Releasealpha-1171-b2, die Seed-ZIPs im Releasealpha-118-b3. - Vergleiche die Prüfsumme mit
SHA256SUMS-otadesselben Releases.SHA256SUMSgilt nur für die UF2. - Lass Funkwerte und Region, wie sie sind. Beim P1 und beim FakeTec blieben sie nach dem Update gleich gemessen.
- Schick dem Repeater
start ota. Er antwortetOK - BLE DFU of the bootloader in 5 sund meldet, dass er bis zu einem Update oder Stromwechsel offline bleibt gemessen. - Nach 5 s wirbt er als DFU-Gerät, am P1 als
SCAP_DFU, am FakeTec mit OTAFIX 2.3 alsPROM_DFU. Bis das Update fertig ist, arbeitet er nicht als Repeater. - Übertrage die ZIP per Bluetooth. Am Mac lief das mit einem Projektskript, das nicht zu den Releases gehört. Auf dem Handy wählst du in nRF Connect das DFU-Gerät und die ZIP offen.
- Danach startet der Knoten von selbst, am P1 nach etwa 15 s, am FakeTec nach höchstens 8 s
gemessen. Prüfe
ver,fuota statusundfuota info.
Am P1 dauerte die Übertragung 134,6 s (Basis) und 192,2 s (Seed), am FakeTec 199,5 s (Basis) und 280,6 s (Seed)
gemessen. Nach der Seed-ZIP zeigte fuota info an beiden Boards ohne
weiteren Befehl passing on update dc7b7cb0 gemessen.
Nur ein DFU-Gerät darf in der Nähe sein, sonst überschreibst du vielleicht ein fremdes.
Bleib dicht am Gerät. Das FakeTec mit AdaDFU verlor Pakete. Ob Signal oder Bootloader
der Grund war, ist nicht getrennt offen. Bleibt das Gerät hängen, trenne den Strom. Dem
FakeTec mit AdaDFU half das nicht. Halte darum den USB-Zugang bereit.
Die ausführliche Fassung steht in der tester-anleitung.md des Releases, Abschnitt 3a.
If you cannot reach your device over USB, use the OTA ZIP file. It puts the same firmware as the UF2 on the device over Bluetooth. Each release carries 18 ZIP files.
Two boards have run on a device, each with the base ZIP and the seed ZIP, one run each
measured. They are the Seeed SenseCAP Solar P1 (S140 7.3.0) and a FakeTec (S140 6.1.1,
bootloader 0.9.2-OTAFIX2.3-BP1.4 according to INFO_UF2.TXT).
With an older bootloader (OTAFIX 1.x, DFU name
AdaDFU) the way is not proven open. A FakeTec that advertised as
AdaDFU lost packets at a weak signal. After the activation it did not come back over USB or
Bluetooth. The cause is open. The name fits OTAFIX 1.x, the version itself is not measured. From a phone the way
is untested open. The remaining boards never ran over Bluetooth.
If you have USB, flash the UF2 instead. Before the update, read the line in INFO_UF2.TXT that starts
with UF2 Bootloader. If it shows OTAFIX 1.x, use the UF2.
- Take the name of the UF2 without
.uf2, plus-ota.zip. The base ZIPs are in the releasealpha-1171-b2, the seed ZIPs in the releasealpha-118-b3. - Compare the checksum with
SHA256SUMS-otaof the same release.SHA256SUMSapplies to the UF2 only. - Leave radio values and region as they are. On the P1 and on the FakeTec they stayed the same after the update measured.
- Send the repeater
start ota. It repliesOK - BLE DFU of the bootloader in 5 sand says it stays offline until an update or a power cycle measured. - After 5 s it advertises as a DFU device, on the P1 as
SCAP_DFU, on the FakeTec with OTAFIX 2.3 asPROM_DFU. Until the update is done, it does not work as a repeater. - Transfer the ZIP over Bluetooth. On the Mac this ran with a project script that is not part of the releases. On a phone you pick the DFU device and the ZIP in nRF Connect open.
- Then the node starts by itself, on the P1 after about 15 s, on the FakeTec after 8 s at most
measured. Check
ver,fuota statusandfuota info.
On the P1 the transfer took 134.6 s (base) and 192.2 s (seed), on the FakeTec 199.5 s (base) and 280.6 s (seed)
measured. After the seed ZIP, fuota info showed
passing on update dc7b7cb0 on both boards without any further command
measured.
Only one DFU device may be nearby, or you may overwrite someone else's. Stay close to the
device. The FakeTec with AdaDFU lost packets. Whether the signal or the bootloader was
the reason is not separated open. If the device gets stuck, cut the power. That did not
help the FakeTec with AdaDFU. So keep USB access ready.
The detailed version is in tester-anleitung.md of the release, section 3a.