MeshCore FUOTA Entwurf zur PrüfungDraft for review

Am Testaufbau gemessen, im Feld beobachtet

Die Funktests am Testaufbau laufen bei SF7 und 1 dBm. Die Alpha-Prüfung nutzte am Testaufbau die Funkwerte des HanseMesh (SF8, 62,5 kHz, 1 dBm). Der Feldtest läuft im echten Mesh. Bisher läuft er nur direkt zwischen Nachbarn im Feld beobachtet (Analyzer, 13. November 2026). Als Beleg zählt der Abgleich mit den gebauten Dateien: laufendes Image und SHA-256 beider Slots. Was noch nicht getestet ist, steht unter Fragen als offen.

Measured on the bench, observed in the field

The radio tests on the bench run at SF7 and 1 dBm. The bench alpha check used the HanseMesh radio settings (SF8, 62.5 kHz, 1 dBm). The field test runs in the real mesh. So far it runs only directly between neighbours observed in the field (analyzer, 13 November 2026). As evidence, we compare the running image and both slots' SHA-256 with the built files. What is not tested yet appears under Questions as open.

Testaufbau

  • Geräte: bis zu 3 FakeTecs und 1 SenseCAP P1. Der Test „Kleineres Image“ und der Dauerlauf nehmen einen Heltec T114 dazu. Der RAK4631, der Xiao und der T096 kamen für einzelne Tests dazu. Die Tests mit Release-Paket laufen auf den FakeTecs A und C, der P1 ist Nachbar.
  • Normaler Repeater: Im Test „Über einen normalen Repeater“ ist der P1 das Relais B. Er läuft mit der unveränderten Firmware 1.18.0, A und C sind FakeTecs.
  • Abstand: rund 50 cm.
  • Funk: Die Funktests laufen bei SF7 und 1 dBm.
  • Airtime-Budget: 10 %. Das ist am Testaufbau zulässig. Bei 1 % dauert derselbe Test 10-mal länger. Im Mesh gelten höchstens 0,3 % im Code geprüft.
  • Kette A-B-C: A ist der Seed. Er ist per USB installiert und bietet das Update an. B holt es von A (Hop 1), C holt es von B (Hop 2). Alle Knoten hören sich. Ein Testfilter in Software stellt die Kette nach.

Bench

  • Devices: up to 3 FakeTecs and 1 SenseCAP P1. The tests “Smaller image” and “Endurance run” add a Heltec T114. The RAK4631, the Xiao and the T096 joined for single tests. The release package tests run on FakeTecs A and C, with the P1 as a neighbour.
  • Normal repeater: In the test “Across a normal repeater” the P1 is relay B. It runs the unchanged firmware 1.18.0, and A and C are FakeTecs.
  • Distance: about 50 cm.
  • Radio: The radio tests run at SF7 and 1 dBm.
  • Airtime budget: 10 %. The bench permits that. At 1 % the same test takes 10 times longer. In the mesh the limit is 0.3 % at most checked in the code.
  • Chain A-B-C: A is the seed. It is installed over USB and offers the update. B pulls it from A (hop 1), C pulls it from B (hop 2). All nodes hear each other. A software test filter recreates the chain.

Die Tests

The tests

TestErgebnis
Tausch ohne Funk, Reset mitten im Tausch
  • Der Tausch dauert 30 bis 39 s.
  • Nach 82 zufälligen Watchdog-Resets mitten im Tausch ist das Ergebnis jedes Mal bitgenau. Ein echter Kabelzug ist nur teilweise getestet offen.
  • Nach 3 Probestarts ohne Bestätigung läuft wieder die alte Firmware (Rückfall) gemessen.
Delta-Patch auf dem Gerät
  • Patches von 6 bis 22 KB ergeben in rund 12 s das neue Image (Ziel-Images von 359 bis 365 KB, 18. Oktober 2026). Beim Release-Image von 299 KB sind es 10,2 s gemessen.
  • Der Hash des neuen Images stimmt exakt gemessen.
Signatur und Manifest
  • Das Manifest ist die signierte Liste von allem, was zu einem Update gehört.
  • Der Knoten lehnt ab, bevor das erste Patch-Fragment kommt.
  • Das gilt für fremden Schlüssel, falsches Gerät, falsche Quelle, Downgrade und schon gescheiterte Updates.
  • Ein verfälschtes Fragment kostet eine Seite: Der Knoten holt sie neu gemessen.
Kette A-B-C
  • Hop 1 ist nach 484,5 s fertig gemessen, vor der Regel „Anfrage an einen Anbieter“ waren es 464 s. Die Rechnung ergibt 486 bis 490 s berechnet.
  • Hop 2 liegt eine Seite hinter Hop 1.
  • Alle Pakete laufen nur über B, mit 0 Duplikaten gemessen.
Zwei Anbieter
  • Zuerst senden beide im Gleichschritt: 41 Duplikate auf 73 Fragmente.
  • Mit der Regel „nicht senden, solange ein Nachbar sendet“ sind es 0 Duplikate.
  • Der Empfänger ist doppelt so schnell fertig wie mit einem Anbieter gemessen.
  • Heute nennt jede Anfrage einen Anbieter, und nur dieser sendet.
Anfrage an einen Anbieter
  • B ist nach 484 s fertig, C nach 696 s, mit 0 Duplikaten.
  • Schweigt der einzige bekannte Anbieter, fragt der Knoten nach 23,5 s alle (0xFFFF).
  • Ein anderer Anbieter liefert. Nach einem Neustart läuft es ebenso.
  • Im Leerlauf liegen 877 s zwischen zwei Angeboten gemessen.
Retract (signierter Rückruf)
  • Eine Fälschung verwirft der Knoten.
  • Ein echter Retract stoppt Pull und Angebot.
  • Er erreicht Nachbarn in Sekunden, auch als Antwort auf ein Angebot.
  • Er übersteht einen Neustart gemessen.
Neustart mitten im Pull
  • Der Knoten meldet „2 of 4 pages checked“ und holt nur den Rest.
  • Eine gesperrte Kampagne bleibt gesperrt gemessen.
  • Seit dem 20. Oktober 2026 sperren Signatur- und Formatfehler die Kampagne nicht mehr. Siehe Angriffe im Detail.
Verlorene Anfrage
  • Wir haben eine Anfrage absichtlich verworfen.
  • Die neue Anfrage kam nach 17,9 bis 25,4 s, vorher nach 108 s gemessen. Seit dem 18. Oktober 2026 kommt ein Zufallsanteil von bis zu 6,4 s dazu, erwartet sind 17,9 bis 24,3 s.
  • Es gab keine zusätzlichen Anfragen und 0 Duplikate gemessen.
Rückfall und gescheitertes Image
  • Nach 3 Probestarts ohne Bestätigung läuft wieder die alte Firmware (Rückfall).
  • Im gemessenen Fall endeten die Probestarts durch Watchdog (fuota hang). Danach lehnte der Knoten das gescheiterte Update ab und bot es nicht an. Er merkt sich die letzten 4 gescheiterten Images.
  • Ein Update von v1 nach v3 klappt gemessen.
Auftrag von Stage-0 abgelehnt
  • Die App gibt Stage-0, dem Lader, der beim Start tauscht, einen Auftrag mit unbekannter Formatversion.
  • Stage-0 bricht vor dem Tausch ab.
  • Die alte Firmware startet, das Image ist gesperrt.
  • Auch nach 5 Minuten mit Auto-Apply „now“ und einem Neustart gibt es keinen neuen Versuch.
  • Dasselbe Update lehnt der Knoten danach ab. Ein Update von v1 nach v3 klappt gemessen.
Ein Layout für S140 6.1.1 und 7.3.0
  • FakeTec (6.1.1) und P1 (7.3.0) laufen im selben Layout, die App ab 0x29000.
  • Das P1-Image, nur mit den 6.1.1-Headern gebaut, ist byte-gleich zum laufenden gemessen.
Ein Image für FakeTec und P1
  • Dasselbe Image läuft auf 2 FakeTecs und 1 P1.
  • Es enthält GPS, ist ohne Testfüllung 374.412 B groß und belegt 92 von 96 Seiten.
  • Jeder Knoten liest sein Board aus dem Deskriptor in der Stage-0-Seite.
  • Eine Kampagne v1→v2 (43 Fragmente) holen FakeTec und P1 in 270 s und 289 s.
  • Beide bestätigen, die Slot-Hashes sind gleich.
  • Auch v2→v4 überlappend läuft auf beiden, und auf dem P1 klappt der Rückfall.
  • Ein FakeTec ohne Deskriptor hat keinen Funk und fällt nach 3 Probestarts ohne Bestätigung zurück gemessen.
RAK4631 am Brett (8. November 2026)
  • Das gemeinsame Image kam über das UF2-Laufwerk des Bootloaders auf das RAK4631. Der Bootloader meldet S140 6.1.1 und die Board-ID WisBlock-RAK4631-Board.
  • Identität (Public Key, Name, Rolle) blieb nach dem Flash unverändert gemessen.
  • Fortsetzen nach einem Neustart mitten im Pull: bestanden in 355 s. Nach dem Neustart holte das RAK4631 20 von 47 Fragmenten.
  • Update über Funk, sofort anwenden: bestanden in 641 s. Das RAK4631 holte 47 Fragmente in 315 s, ohne Duplikate und ohne falsche Fragmente, und bestätigte Build 2 gemessen.
  • Anbieter war ein FakeTec. Test-Schlüssel, SF7, 1 dBm, nur Zero-Hop.
  • Nicht gefahren: der serielle DFU-Weg offen.
  • Nachweislauf 1.17.1 nach 1.18.0 am 9. November: bestanden. Die Kampagne hatte 145 Fragmente. Das RAK4631 war nach 9 h 21 min vollständig. Es wandte den Patch (299.284 B) in 10.241 ms an und bestätigte seinen Testboot selbst. Der zweite Empfänger, ein FakeTec, war nach 9 h 35 min fertig. Null abgelehnte Pakete, null Signaturfehler, kein Paket ging als Flut hinaus gemessen.
  • Befund dabei: ein Testboot muss in seiner Frist ein Paket gehört und selbst gesendet haben, sonst startet er neu. Am stillen Brett hörte der FakeTec nach seinem Neustart 18 Minuten nichts und hätte seinen Testboot nicht von allein bestätigt, deshalb kam die Bestätigung von Hand. Ob das in einem Netz mit normalem Verkehr überhaupt auftritt, ist nicht geprüft; dort zählt jedes akzeptierte Paket, auch die Adverts der Nachbarn offen.
Überlappend anwenden, Fenster
  • Ein Patch mit 4 Seiten passt nicht hinter ein Image mit 94 Seiten.
  • Im Fenster gibt der Knoten den Patch weiter.
  • Ein zweiter Knoten holt ihn dort komplett, mit 0 Duplikaten.
  • 180 s nach der letzten Lieferung wendet der Knoten überlappend an.
  • Der Lese-Abstand beträgt 8.192 B. Das Image neu aufzubauen dauert 12,8 s.
  • Er bestätigt und bietet danach nichts mehr an.
  • Passt der Patch dahinter, wendet er sofort an und bietet weiter an gemessen.
P1 über Funk
  • Der P1 holt 72 Fragmente von einem FakeTec, der die P1-Kampagne nur weitergibt.
  • Er wendet überlappend an. Der Lese-Abstand ist 8.139 B, gleich der Prüfung am Rechner.
  • Er bestätigt.
  • Auch auf dem P1 folgt nach 3 Probestarts ohne Bestätigung der Rückfall gemessen.
Größenwächter
  • Ein Image über 96 Seiten bricht den Build ab (FakeTec und P1) gemessen.
Kleineres Image (-Os) auf Hardware
  • v1 kommt per USB auf 2 FakeTecs, 1 P1 und 1 T114, alle bestätigen.
  • Jeder Knoten erkennt sein Board am Deskriptor.
  • USB meldet wie vorher nur die serielle Schnittstelle.
  • 3 Knoten holen eine Kampagne v1→v2 in 4,4 bis 4,7 min über Funk.
  • Überlappend v2→v3 mit Fenster: Der Lese-Abstand ist 5.013 B, gleich der Prüfung am Rechner.
  • Die Slot-Hashes gleichen dem gebauten Image.
  • Der 1200-Baud-Sprung führt ins serielle DFU.
  • Das Bootstrap per adafruit-nrfutil schreibt Stage-0 an 0x26000.
  • Der Knoten startet danach und behält seinen Schlüssel.
  • Ohne Display-Treiber schaltet langes Drücken der Taste den FakeTec weiterhin aus gemessen.
Kette A-B-C bei 1 %
  • Hop 1 ist nach 4.664 s fertig gemessen. Die Rechnung ergab 4.694 s berechnet, das 10-Fache des Laufs bei 10 %.
  • Das Budget war über eine Stunde mit 1,02 % belegt berechnet. Dazu kommen die normalen Adverts des Repeaters.
  • Hop 2 war nach 7.053 s fertig gemessen, die Rechnung ergab 6.192 s berechnet.
  • Der Grund: Eine verlorene Anfrage kostete 15 min (siehe Was noch offen ist) gemessen.
Über einen normalen Repeater
  • B läuft mit der unveränderten Firmware 1.18.0 (Release-Paket).
  • Dort ist nur die Test-Region eingetragen, der Flood-Scope des Flut-Angebots.
  • A und C hören sich laut Testfilter nicht direkt.
  • Der Test lief 2-mal, vor und nach den Korrekturen aus einem Review.
  • Das Flut-Angebot von A kommt über B bei C an.
  • 4 Anfragen und 37 Fragmente laufen per Pfad über B, ohne Verlust.
  • Die Kampagne ist nach 466 s und 467 s vollständig und bestätigt gemessen.
Release-Paket per USB (Seed werden)
  • Per UF2 und per seriellem DFU installiert. Der Knoten übernimmt die Kampagne aus dem Paket und bietet sie an gemessen.
  • Ein Paket mit Stage-0 richtet per UF2 einen neuen Knoten ein gemessen.
  • Ein älteres Paket lehnt der Knoten ab. Er bietet weiter die neuere Kampagne an gemessen.
  • Die erste Fassung des Pakets war per UF2 nicht installierbar: Der Bootloader schreibt nur unterhalb 0xEA000 gemessen. Darum liegt die Kampagne im Paket am Anfang von Slot B.
  • Ungetestet: ein Stromausfall, während der Knoten die Kampagne verschiebt offen.
Vom Paket-Seed zum Nachbarn
  • Ein Nachbar holt die Kampagne über Funk vom Seed, mit 4 Anfragen und 27 Datenpaketen gemessen.
  • Er wendet sie nach der Wartezeit an, auch über einen Neustart hinweg, und bestätigt das neue Image gemessen. Der Test-Build wartet 120 s statt 7 Tagen.
  • Ein Retract während der Wartezeit stoppt das Anwenden gemessen.
  • Flut-Angebote: Der Test-Build flutet höchstens 2-mal frisch, der Zähler übersteht einen Neustart. Nach einer gehörten Anfrage flutet der Seed, nach einer alten nicht gemessen.
Dauerlauf 12 h
  • Auf FakeTec, P1 und T114 liefen 4 Test-Releases im Abstand von 3 h.
  • Die Knoten holten jede Kampagne über Funk und bestätigten sie, hinter dem Image und überlappend.
  • Es gab keine unerwarteten Neustarts.
  • Der geplante Rückfall lief nicht, weil das Testwerkzeug die Bootmeldung des T114 verpasste.
Xiao und T096 am Testaufbau (11. November 2026)
  • Beide Boards wurden am Deskriptor erkannt, der Funk lief. Gegenstelle war ein FakeTec, SF7, 1 dBm, nur Zero-Hop gemessen.
  • Der Xiao empfing den FakeTec mit RSSI -47 und SNR 11,75. Der FakeTec empfing den Xiao ebenfalls gemessen.
  • Der T096 empfing den FakeTec mit RSSI -16. Der FakeTec empfing den T096 mit RSSI -33 gemessen.
  • Der Xiao hat den Bootloader 0.6.1 ohne OTAFIX. Der T096 hat den Bootloader 0.9.0 mit dem Zusatz -dirty. Ob er OTAFIX hat, ist nicht geprüft offen.
  • Nicht geprüft: FUOTA-Pull über Funk, LED und Taste, fuota uf2, serielles DFU und Rückfall offen.
Alpha-Prüfung (12. November 2026, mit Release-Images und HanseMesh-Funkwerten)
  • Ein Knoten mit 1.17.1-b2 holte die Kampagne dc7b7cb0 (174 Fragmente) von einem Seed mit 1.18.0-b3. Nach 12,6 h wandte er sie an und bestätigte den Testboot ohne Zutun gemessen.
  • Ein Manifest mit Test-Schlüssel lehnte der Knoten ab (ERR manifest signature) und blieb unverändert gemessen.
  • Er hielt eine signierte Kampagne für Build 2 (dc048c3d) nur als Relais. Für sich lehnte er sie ab (not for this node) gemessen. Ob Build oder Basis-Hash der Grund war, ist nicht getrennt offen.
  • Der Rückfall ohne Nachbarn am Release-Image ist nicht getestet. Er braucht einen abgeschirmten Aufbau offen.
Probelauf 1.17.1-b2 auf 1.18.0-b3 (Test-Schlüssel, Nacht vom 11. auf den 12. November 2026)
  • Zwei Knoten mit 1.17.1-b2 holten das Update über Funk von einem Knoten mit 1.18.0-b3. Sie prüften es, wandten es an und bestätigten ohne Eingriff gemessen.
  • Von „pulling“ bis „confirmed“ vergingen rund 18 min. Das waren 14 min Funk und 2 min Wartezeit, dazu Umbau und Testboot gemessen. Es waren Test-Images bei SF7 und 1 dBm, nicht das Release-Timing.
  • Der Knoten mit 1.18.0-b3 bestätigte beim ersten und zweiten Flash nicht und fiel zurück. Beim dritten Flash bestätigte er, nachdem ein Nachbar alle 12 s ein Advert sendete gemessen. Dass in der stillen Umgebung kein Paket ankam, ist nicht geprüft offen.
Feld: Alpha-Test mit Testern
  • Die Kampagne dc7b7cb0 (Build 3) läuft seit dem 12. November 2026 mit zwei Tester-Knoten im Feld beobachtet (Analyzer, 13. November 2026).
  • Der Analyzer hört sie nur direkt (Zero-Hop) über einen Beobachter im Feld beobachtet.
  • Der Lauf ist nicht vollständig offen.
TestResult
Swap without radio, reset mid-swap
  • The swap takes 30 to 39 s.
  • After 82 random watchdog resets mid-swap, the result is bit-exact every time. A real cable pull is only partly tested open.
  • After 3 test boots without confirmation the old firmware runs again (revert) measured.
Delta patch on the device
  • Patches of 6 to 22 KB become the new image in about 12 s. The target images were 359 to 365 KB (18 October 2026). For the release image of 299 KB it is 10.2 s measured.
  • The hash of the new image matches exactly measured.
Signature and manifest
  • The manifest is the signed list of everything that belongs to an update.
  • The node refuses before the first patch fragment arrives.
  • That covers a foreign key, wrong device, wrong source, downgrade and an already failed update.
  • A corrupted fragment costs one page: the node pulls it again measured.
Chain A-B-C
  • Hop 1 is done after 484.5 s measured; before the rule "request to one provider" it was 464 s. The calculation gives 486 to 490 s calculated.
  • Hop 2 is one page behind hop 1.
  • All packets go only through B, with 0 duplicates measured.
Two providers
  • At first both send in lockstep: 41 duplicates out of 73 fragments.
  • With the rule “do not send while a neighbour is sending” there are 0 duplicates.
  • The receiver finishes twice as fast as with one provider measured.
  • Today every request names one provider, and only that provider sends.
Request to one provider
  • B is done after 484 s and C after 696 s, with 0 duplicates.
  • If the only known provider stays silent, the node asks everybody (0xFFFF) after 23.5 s.
  • Another provider delivers. After a reboot it works the same way.
  • When idle, 877 s pass between two offers measured.
Retract (signed recall)
  • The node drops a forgery.
  • A genuine retract stops the pull and the offer.
  • It reaches neighbours within seconds, also as a reply to an offer.
  • It survives a reboot measured.
Reboot in the middle of a pull
  • The node reports “2 of 4 pages checked” and pulls only the rest.
  • A banned campaign stays banned measured.
  • Since 20 October 2026, signature and format errors no longer ban the campaign. See attacks in detail.
Lost request
  • We dropped a request on purpose.
  • The new request came after 17.9 to 25.4 s, where it used to take 108 s measured. Since 18 October 2026 a random share of up to 6.4 s is added, so 17.9 to 24.3 s is expected.
  • There were no extra requests and 0 duplicates measured.
Revert and failed image
  • After 3 test boots without confirmation the old firmware runs again (revert).
  • In the measured case the test boots ended in a watchdog restart (fuota hang). The node then rejected the failed update and did not offer it. It remembers the last 4 failed images.
  • An update from v1 to v3 works measured.
Job refused by Stage-0
  • Stage-0 is the loader that swaps at boot. The app gives it a job with an unknown format version.
  • Stage-0 aborts before the swap.
  • The old firmware starts, and the image is blocked.
  • Even 5 minutes of auto apply “now” and a reboot bring no new attempt.
  • The node rejects the same update afterwards. An update from v1 to v3 works measured.
One layout for S140 6.1.1 and 7.3.0
  • FakeTec (6.1.1) and P1 (7.3.0) run in the same layout, with the app from 0x29000.
  • The P1 image, built only with the 6.1.1 headers, is byte-identical to the running one measured.
One image for FakeTec and P1
  • The same image runs on 2 FakeTecs and 1 P1.
  • It includes GPS, is 374,412 B without test filler and fills 92 of 96 pages.
  • Every node reads its board from the descriptor in the Stage-0 page.
  • FakeTec and P1 pull a campaign v1→v2 (43 fragments) in 270 s and 289 s.
  • Both confirm, and the slot hashes are the same.
  • Overlapping v2→v4 also runs on both, and the revert works on the P1.
  • A FakeTec without descriptor has no radio and reverts after 3 test boots without confirmation measured.
RAK4631 on the bench (8 November 2026)
  • The shared image went onto the RAK4631 through the UF2 drive of the bootloader. The bootloader reports S140 6.1.1 and the board ID WisBlock-RAK4631-Board.
  • Identity (public key, name, role) stayed unchanged after the flash measured.
  • Resume after a restart in the middle of a pull: passed in 355 s. After the restart the RAK4631 pulled 20 of 47 fragments.
  • Update over the air, apply at once: passed in 641 s. The RAK4631 pulled 47 fragments in 315 s, with 0 duplicates and 0 bad fragments, and confirmed build 2 measured.
  • The provider was a FakeTec. Test key, SF7, 1 dBm, zero hop only.
  • Not run: the serial DFU route open.
  • Proof run 1.17.1 to 1.18.0 on 9 November: passed. The campaign had 145 fragments. The RAK4631 was complete after 9 h 21 min. It applied the patch (299,284 B) in 10,241 ms and confirmed its test boot by itself. The second receiver, a FakeTec, finished after 9 h 35 min. Zero rejected packets, zero signature errors, and no packet went out as a flood measured.
  • Finding along the way: a test boot needs two things within its deadline. It must have heard a packet and completed a send of its own. Otherwise it restarts. On the quiet bench the FakeTec heard nothing for 18 minutes after its restart. It would not have confirmed its test boot on its own, so the confirmation came by hand. Whether this happens in a network with normal traffic is untested. There every accepted packet counts, including the neighbours' adverts open.
Overlapping apply, window
  • A patch of 4 pages does not fit behind an image of 94 pages.
  • During the window the node passes the patch on.
  • A second node pulls all of it there, with 0 duplicates.
  • 180 s after its last delivery the node applies overlapping.
  • The read margin is 8,192 B. Rebuilding the image takes 12.8 s.
  • The node confirms and offers nothing afterwards.
  • If the patch fits behind the image, the node applies at once and keeps offering measured.
P1 over the air
  • The P1 pulls 72 fragments from a FakeTec, which only passes the P1 campaign on.
  • It applies overlapping. The read margin is 8,139 B, as in the check on the computer.
  • It confirms.
  • On the P1, too, the revert follows after 3 test boots without confirmation measured.
Size guard
  • An image above 96 pages stops the build (FakeTec and P1) measured.
Smaller image (-Os) on hardware
  • v1 goes onto 2 FakeTecs, 1 P1 and 1 T114 over USB, and all confirm.
  • Every node identifies its board by the descriptor.
  • USB reports only the serial port, as before.
  • 3 nodes pull a campaign v1→v2 over the air in 4.4 to 4.7 min.
  • Overlapping v2→v3 with window: read margin 5,013 B, as in the check on the computer.
  • The slot hashes equal the built image.
  • The 1200 baud touch leads into the serial DFU.
  • The bootstrap through adafruit-nrfutil writes Stage-0 at 0x26000.
  • The node starts afterwards and keeps its key.
  • Without the display driver, a long press of the button still switches the FakeTec off measured.
Chain A-B-C at 1 %
  • Hop 1 is done after 4,664 s measured. The calculation gave 4,694 s calculated, 10 times the 10 % run.
  • Over one hour the budget was used to 1.02 % calculated. The repeater's regular adverts come on top.
  • Hop 2 was done after 7,053 s measured, where the calculation gave 6,192 s calculated.
  • The reason: one lost request cost 15 min (see What is still open) measured.
Across a normal repeater
  • B runs the unchanged firmware 1.18.0 (release package).
  • Only the test region is entered there, the flood scope of the flooded offer.
  • A and C do not hear each other directly, by test filter.
  • The test ran twice, before and after the fixes from a review.
  • A's flooded offer reaches C through B.
  • 4 requests and 37 fragments travel along the path through B without loss.
  • The campaign is complete and confirmed after 466 s and 467 s measured.
Release package over USB (becoming the seed)
  • Installed by UF2 and by serial DFU. The node takes over the campaign from the package and offers it measured.
  • A package with Stage-0 sets up a new node by UF2 measured.
  • The node rejects an older package. It keeps offering the newer campaign measured.
  • The first version of the package could not be installed by UF2: the bootloader writes only below 0xEA000 measured. That is why the package holds the campaign at the start of slot B.
  • Untested: a power cut while the node moves the campaign open.
From the package seed to a neighbour
  • A neighbour pulls the campaign over the air from the seed, with 4 requests and 27 data packets measured.
  • It applies it after the waiting time, also across a reboot, and confirms the new image measured. The test build waits 120 s instead of 7 days.
  • A retract during the waiting time stops the apply measured.
  • Flooded offers: the test build floods fresh at most 2 times, and the counter survives a reboot. After a request it heard, the seed floods; after an old one, it does not measured.
Endurance run 12 h
  • 4 test releases ran on FakeTec, P1 and T114, 3 h apart.
  • The nodes pulled and confirmed every campaign over the air, behind the image and overlapping.
  • There were no unexpected reboots.
  • The planned revert did not run: the test tool missed the T114's boot message.
Xiao and T096 on the bench (11 November 2026)
  • Both boards were recognised by their descriptor, and the radio ran. The counterpart was a FakeTec, SF7, 1 dBm, zero-hop only measured.
  • The Xiao received the FakeTec at RSSI -47 and SNR 11.75. The FakeTec received the Xiao too measured.
  • The T096 received the FakeTec at RSSI -16. The FakeTec received the T096 at RSSI -33 measured.
  • The Xiao has bootloader 0.6.1 without OTAFIX. The T096 has bootloader 0.9.0 with the suffix -dirty. Whether it has OTAFIX is not checked open.
  • Not checked: FUOTA pull by radio, LED and button, fuota uf2, serial DFU and revert open.
Alpha check (12 November 2026, with release images and HanseMesh radio settings)
  • A node with 1.17.1-b2 pulled the campaign dc7b7cb0 (174 fragments) from a seed with 1.18.0-b3. After 12.6 h it applied it and confirmed the test boot without any action measured.
  • The node refused a manifest signed with the test key (ERR manifest signature) and stayed unchanged measured.
  • The node held a signed campaign for build 2 (dc048c3d) only as a relay. It refused it for itself (not for this node) measured. Whether build or base hash was the reason is not separated open.
  • The revert without neighbours on the release image is not tested. It needs a shielded setup open.
Trial run 1.17.1-b2 to 1.18.0-b3 (test key, night of 11 to 12 November 2026)
  • Two nodes with 1.17.1-b2 pulled the update over the air from a node with 1.18.0-b3. They checked it, applied it and confirmed without any action measured.
  • From “pulling” to “confirmed” took about 18 min. That was 14 min of radio and 2 min of waiting time, plus the swap and the test boot measured. These were test images at SF7 and 1 dBm, not the release timing.
  • The node with 1.18.0-b3 did not confirm at the first two flashes and fell back. The third flash confirmed once a neighbour sent an advert every 12 s measured. That no packet arrived in the quiet surroundings is not checked open.
Field: alpha test with testers
  • The campaign dc7b7cb0 (build 3) has run since 12 November 2026 with two tester nodes observed in the field (analyzer, 13 November 2026).
  • The analyzer hears it only directly (zero-hop) through one observer observed in the field.
  • The run is not complete open.

Weiter: FragenNext: Questions →